UKCA Marking for PVC Wall Panels: Post-Brexit UK Market Guide
This guide explains the UKCA marking requirements for PVC wall panels: the GB-CPR framework, designated standards, UK Approved Bodies, the Declaration of Performance, Northern Ireland’s separate regime under the Windsor Framework, and how to verify a supplier’s compliance documentation.
1. What Is UKCA Marking?
UKCA (UK Conformity Assessed) marking is the UK’s own product conformity mark, introduced after the UK left the European Union’s single market on 1 January 2021. It covers most goods previously requiring CE marking when placed on the Great Britain market — England, Scotland, and Wales.
The UKCA mark follows a structure closely parallel to CE marking: the manufacturer conducts a conformity assessment, compiles a technical documentation file, issues a Declaration of Performance (for construction products), and affixes the UKCA mark. The key difference is that where third-party conformity assessment is required for the UKCA route, it must be carried out by a UK Approved Body — the UK equivalent of an EU Notified Body — and the documentation references UK legislation and UK designated standards rather than EU directives and harmonised standards.
- Market scope: UKCA applies to Great Britain (England, Scotland, Wales); CE applies to the EU single market and Northern Ireland
- Assessment body: the UKCA route uses a UK Approved Body; the CE route uses an EU Notified Body (where third-party assessment applies)
- Standards: the UKCA route references UK designated standards (e.g., EN 15102 or BS EN 15102); CE references EU harmonised standards — currently identical in substance
- Declaration: the UKCA route uses a DoP under the GB regime; CE uses an EU DoP — for construction products, both are Declarations of Performance under their respective regulatory frameworks
- Mark appearance: UKCA uses the letters “UKCA” in a prescribed format; CE uses the letters “CE”
It is important to understand that the UKCA mark is not recognised on the EU market. A product bearing only the UKCA mark cannot be placed on the EU market or the Northern Ireland market. Conversely, a product bearing the CE mark can currently be placed on the GB market, because the UK government continues to recognise CE marking for construction products — subject to the conditions of the current GB framework.
2. GB-CPR: The UK’s Construction Products Regulation
The UK’s construction products regulations stem from its former EU membership. The EU Construction Products Regulation 2011 (EU-CPR 2011, Regulation EU 305/2011) was implemented in the UK in 2013. Following Brexit, the EU-CPR 2011 was retained as UK law — now referred to as the GB-CPR (Great Britain Construction Products Regulation). It was amended in 2020 and 2022 to reflect the Northern Ireland Protocol and to grant enforcement powers to the Secretary of State for Housing, Communities and Local Government (MHCLG).
The GB regime remains closely aligned with the EU regime. GB-CPR applies where products are subject to mandatory designated standards (designated by the Secretary of State) or are subject to a UK technical assessment. These designated standards largely mirror EU harmonised standards. The Construction Products (Amendment) Regulations 2025 came into force on 8 January 2026 to enable CE-marked products compliant with the reformed EU-CPR 2024 to be placed on the GB market without further assessment.
Key Principles of GB-CPR
- Designated standards: products must be assessed against UK designated standards (references may carry BS, EN, EN ISO, or EN IEC prefixes) or UK technical assessments
- Declaration of Performance (DoP): manufacturers must issue a DoP declaring the product’s essential characteristics and performance levels
- Factory Production Control (FPC): manufacturers must maintain a documented quality management system ensuring consistent production
- AVCP (Assessment and Verification of Constancy of Performance): products are assigned to an AVCP system that determines the level of third-party involvement — the same system as under EU-CPR
- Conformity marking: the UKCA mark or CE mark must be affixed to the product, its packaging, or accompanying documents
While CE marking is currently recognised for construction products in Great Britain, the UK government has stated that any future withdrawal of CE recognition would be subject to a minimum two-year transitional period. The UK is also developing a reformed construction products regulatory framework, so manufacturers should monitor developments, as UK and EU requirements may diverge over time.
3. Designated Standards for PVC Wall Panels
Under GB-CPR, construction products must be assessed against UK designated standards. These are standards designated by the Secretary of State and published with a formal notice on GOV.UK. Since Brexit, all existing EU harmonised European standards (hENs) became UK designated standards on day one, and the list has been updated since.
For PVC wall panels, the applicable designated standard depends on the product type, form, and intended use:
| Designated Standard | Scope | Key Characteristics Declared | Applicability |
|---|---|---|---|
| EN 15102 / BS EN 15102 | Decorative wall coverings — roll and panel form (adhesive-fixed) | Reaction to fire, formaldehyde release, heavy metals migration, vinyl chloride monomer (VCM) | Primary standard for adhesive-fixed decorative wall coverings, including PVC wallcovering panels |
| BS EN 13245-2 | Plastics — Rigid PVC-U profiles for internal and external wall and ceiling finishes | Mechanical, reaction to fire, dangerous substances | Alternative — if classified as rigid PVC-U profile (less common for decorative panels) |
| BS EN 14041 | Resilient, textile, laminate and modular multilayer floor coverings | Reaction to fire, formaldehyde, VOC emissions | If panels are also used as floor coverings |
Two Points That Catch Suppliers Out
1. Do not hardcode a standard version. EN 15102:2019 replaced the earlier 2007+A1:2011 edition (which BSI has withdrawn) and narrowed the title to “Decorative wallcoverings — Roll form”. Depending on the product form, fixing method, and the version listed on the UK designated standards list, the applicable designation may differ. Always verify the current designated version on the UK government’s designated standards list before preparing compliance documentation.
2. The prefix matters less than you think. UK designated standards may be published with a BS, EN, EN ISO, or EN IEC prefix. Where the designated standard is listed with an EN prefix, UK government guidance confirms it is acceptable to reference either the EN version or a national-prefixed version (e.g., BS EN) of the identical standard in technical documentation. What matters is that the documentation references the designated standard applicable to the product and intended use.
In practice, when UK buyers ask about UKCA marking for PVC wall panels, the most common question is not “Do you have UKCA?” — it’s “Can you supply CE-marked panels for the UK market, or do we need UKCA?” Because CE marking is currently recognised in Great Britain, a product that already has EU CE certification with a valid DoP and Notified Body test reports can generally be placed on the GB market without obtaining UKCA marking. This is the simplest route for manufacturers who already serve EU markets. However, UK distributors sometimes request UKCA marking because their end customers or specifiers specifically ask for it — in that case, UKCA certification through a UK Approved Body is the route to follow.
4. CE or UKCA: Which Mark Do You Need?
For construction products placed on the Great Britain market, manufacturers currently have a choice: CE marking or UKCA marking. Both are legally accepted. The decision depends on the manufacturer’s market strategy and commercial requirements:
| Scenario | Recommended Mark | Rationale |
|---|---|---|
| Manufacturer already has EU CE certification | CE (currently recognised in GB) | No additional assessment needed for GB market access, provided the applicable EU and GB standard requirements are aligned |
| Manufacturer serves both EU and UK markets | CE — where requirements align, or dual UKCA + CE | CE is currently recognised in both GB and the EU; add UKCA only if commercial requirements or requirement divergence make it necessary |
| UK distributor or specifier explicitly requires UKCA | UKCA (through UK Approved Body) | Commercial requirement — some buyers prefer or specify the UK mark |
| Manufacturer serves only the UK market | UKCA or CE | Both accepted; UKCA may be preferred for brand positioning in the UK |
| Product placed on Northern Ireland market | CE (or CE + UKNI) | Northern Ireland follows EU rules under the Windsor Framework |
| Product placed on both GB and Northern Ireland markets | CE (recognised in both) or dual UKCA + CE | CE is currently accepted in both GB and NI; UKCA alone is not accepted in NI |
Marking by UK Market
| Market | Accepted Marking | Framework |
|---|---|---|
| England | UKCA or CE* | GB construction products regime |
| Scotland | UKCA or CE* | GB construction products regime |
| Wales | UKCA or CE* | GB construction products regime |
| Northern Ireland | CE / CE + UKNI | EU CPR under the Windsor Framework |
| European Union | CE | EU CPR |
*CE recognition in Great Britain is subject to the current UK regulatory framework and applicable conditions. Always verify the latest UK government requirements before placing a product on the market.
Although CE marking is currently recognised in Great Britain, the UK government retains the ability to withdraw this recognition in the future, with a minimum two-year transitional period. If you are investing in new product certification and expect to serve the UK market long-term, consider whether UKCA marking — obtained in parallel with or after CE marking — provides additional commercial assurance. The technical file prepared for CE marking can largely serve as the basis for UKCA marking with adaptations for UK legislation and standards references.
5. UK Approved Bodies: The UK Equivalent of Notified Bodies
For AVCP systems that require third-party involvement (for decorative wall coverings, typically System 3 — initial type testing by a conformity assessment body), the conformity assessment for the UKCA route must be carried out by a UK Approved Body. A UK Approved Body is a conformity assessment body designated under the GB construction products regime and listed on the UK Market Conformity Assessment Bodies (UKMCAB) database. UKAS is the UK’s national accreditation body for the construction products framework.
UK Approved Bodies are the GB equivalents of EU Notified Bodies. Their responsibilities include:
- Performing initial type testing against the designated standard
- Issuing certificates of constancy of performance (where the AVCP system requires it)
- Conducting ongoing factory audits and surveillance (where the AVCP system requires it)
- Providing the UK Approved Body identification number where the applicable system requires it to accompany the marking
Finding a UK Approved Body
The UK government maintains a Find a Conformity Assessment Body service where you can search the UKMCAB database for UK Approved Bodies by product area and designated standard. For decorative wall coverings, look for approved bodies whose scope covers the applicable EN 15102 designation.
If your product already has CE marking through an EU Notified Body, obtaining UKCA marking does not necessarily mean starting from scratch. Where a manufacturer already has EU conformity documentation, the UK Approved Body should be consulted to determine what existing test evidence can be used and whether additional assessment is required. In many cases existing test reports can support the UKCA assessment, avoiding duplicate testing — but this depends on the product, the applicable standards and AVCP system, and the Approved Body’s own review, so expect a review process rather than an automatic transfer.
6. Declaration of Performance Under GB-CPR
The Declaration of Performance is the core document of construction product conformity, for both UKCA and CE marking. Under GB-CPR, the manufacturer issues a DoP that declares the product’s essential characteristics and performance levels, based on assessment against the designated standard.
What the UK DoP Must Include
| # | Required Element | Example |
|---|---|---|
| 1 | Product intended use | Interior decorative wall finish |
| 2 | Product type identification | PVC Marble Wall Panel PMW-5001 |
| 3 | Manufacturer name and address | CENCHER INDUSTRY SHANGHAI CO., LTD. |
| 4 | Authorised representative (if appointed) | UK-based authorised representative or importer |
| 5 | AVCP system | System 3 (example only — confirm against Annex ZA of the applicable designated standard and the declared intended use) |
| 6 | Designated standard | EN 15102 / BS EN 15102 — the applicable designated version |
| 7 | UK Approved Body reference | Approved Body No. XXXX (where the AVCP system allocates tasks to an approved body, e.g., initial type testing) |
| 8 | Declared performance for essential characteristics | See performance table |
| 9 | Date and place of issue | Shanghai, 2026-08-27 |
| 10 | Signature of authorised person | Technical Director |
Essential Characteristics for Decorative Wall Coverings (EN 15102)
The table below reflects the assessment methods referenced by EN 15102 for decorative wall coverings. The performance values shown are illustrative examples only — each declared value must be supported by valid test or assessment evidence for the specific product:
| Essential Characteristic | Declared Performance (Example Only) | Assessment Method |
|---|---|---|
| Reaction to fire | [The classification supported by the product’s valid test evidence — e.g., B-s1,d0 only where supported by test reports or permitted classification without testing] | EN 13501-1 classification (test evidence via EN 13823 / EN ISO 11925-2) |
| Formaldehyde release | e.g., ≤ 120 mg/kg | EN 12149 (formaldehyde release) |
| Heavy metals and specific elements migration | e.g., Pb ≤ 90 mg/kg, Cd ≤ 25 mg/kg | EN 12149 (migration of heavy metals and certain other elements) |
| Vinyl chloride monomer (VCM) release | e.g., ≤ 0.2 mg/kg | EN 12149 (VCM release) |
| Emission of dangerous substances into indoor air | Declared where required (e.g., per EN 16516) | EN 16516 / as specified by the applicable standard version |
The DoP should be provided in English for the GB market. For products sold across both GB and EU markets, whether a single DoP can serve both regimes depends on the applicable standards, versions, and legislative references — confirm with your Approved Body or Notified Body whether one document suffices or separate EU and GB DoPs are needed.
7. UKCA Mark Application: What Goes on the Product
Once the DoP is issued and the FPC is in place, the UKCA mark must be affixed in accordance with the GB construction products requirements. The marking rules follow the retained CPR framework rather than the general goods rules that apply to other UKCA-regulated sectors. For construction products, the UKCA mark can generally be placed on:
- The product itself — on the back of each panel, or on a durable label affixed to each panel, OR
- The packaging — where the nature of the product does not allow direct marking, AND/OR
- The accompanying commercial documents — where the applicable requirements permit, e.g., delivery note, invoice, or product data sheet
Note: the UKCA labelling easement that runs until 31 December 2027 for many general consumer goods (allowing the mark on a temporary label or accompanying document) does not apply to construction products — construction products are specifically excluded from that measure. Follow the marking provisions of the GB construction products regime and the applicable designated standard (its Annex ZA usually specifies marking and labelling requirements).
What Information Must Accompany a UKCA-Marked Construction Product?
Beyond the UKCA logo itself, the information that accompanies the product under the GB construction products regime includes:
- Manufacturer identification — the manufacturer’s name, registered trade name or trademark, and postal address
- Product-type identification — product type, batch or serial number where applicable
- DoP reference — identification of the Declaration of Performance on which the marking is based
- Declared performance — the essential characteristics and performance levels declared in the DoP
- Reference to the applicable designated standard — e.g., the applicable designated version of EN 15102
- UK Approved Body number — where the applicable AVCP system allocates tasks to an approved body and requires its number to accompany the marking
- Economic operator information — importer or authorised representative identification where required by the applicable requirements
A product may carry both the CE mark and the UKCA mark where it meets the applicable EU and GB requirements. Where both marks are used, each must comply with its own rules — the CE mark references the EU Notified Body number where applicable, and the UKCA mark references the UK Approved Body number where applicable. The supporting documentation and conformity assessment arrangements should be checked separately for each market and product route: whether they can share a single technical file or require separate documentation depends on the applicable legislation, AVCP system, assessment bodies, and standards for each route.
8. Northern Ireland: CE, UKNI, and the Windsor Framework
Northern Ireland follows a different regulatory regime from Great Britain. Under the Windsor Framework (formerly the Northern Ireland Protocol), products placed on the Northern Ireland market follow EU rules — not UK rules.
| Scenario | Required Mark | Notes |
|---|---|---|
| Product assessed by an EU Notified Body, placed on NI market | CE | Standard EU CE marking — no additional UK mark needed |
| Product assessed by a UK Approved Body, placed on NI market | CE + UKNI | UKNI mark must accompany the CE mark — cannot be used alone |
| UKCA-marked product placed on NI market | Not accepted | UKCA alone is not valid in Northern Ireland |
| Qualifying Northern Ireland goods placed on GB market | CE or CE + UKNI | Unfettered access — NI goods can be sold in GB with CE marking |
The UKNI mark is a supplementary indicator that accompanies the CE mark when a UK Approved Body has carried out the conformity assessment for a product destined for Northern Ireland. It cannot be used in isolation. If your product is placed on the Northern Ireland market, it must carry CE marking (with UKNI if assessed by a UK body). Applying UKCA marking alone to goods for Northern Ireland is a compliance error that can result in market withdrawal.
For manufacturers supplying both Great Britain and Northern Ireland, the most efficient approach is usually to obtain CE marking through an EU Notified Body. CE marking is accepted in both GB (under the current recognition) and Northern Ireland (under the Windsor Framework), covering both markets with a single certification — provided the applicable EU and GB standard requirements remain aligned. UKCA marking alone covers only GB; adding it does not help with Northern Ireland access.
9. Requirements for Non-UK Manufacturers
For manufacturers based outside the UK — including manufacturers in China, as is the case for many PVC wall panel suppliers — supplying construction products to the GB market involves identifying the economic operator responsible for the product under the applicable GB requirements. The specific obligations depend on the applicable legislation, the marking route (CE or UKCA), and the manufacturer’s market presence, so they should be confirmed for each product and supply arrangement.
Importer vs Authorised Representative
Two roles commonly fulfil this function:
- An importer established in the UK who places the product on the GB market — responsible for verifying that the manufacturer has carried out the correct conformity assessment and that the product bears the correct marking and is accompanied by the required documentation
- An authorised representative appointed by the manufacturer and established in the UK — carries out tasks specified in the manufacturer’s mandate and acts as the contact point for UK market surveillance authorities
The responsible economic operator is generally responsible for:
- Ensuring the manufacturer has carried out the correct conformity assessment and drawn up the technical documentation
- Ensuring the correct marking has been affixed
- Providing the identification and contact details required by the applicable GB requirements, in the prescribed manner
- Cooperating with UK market surveillance authorities and providing documentation on request
- Keeping technical documentation for the period required by the applicable legislation (10 years is the common retention period under the retained construction products framework)
When we export PVC wall panels to UK distributors, the most common arrangement is that the UK importer acts as the responsible economic operator for the shipment. We provide the manufacturer’s documentation — DoP, test reports, FPC records — and the importer retains copies and handles any market surveillance enquiries. Some UK buyers instead appoint an authorised representative for this role, particularly when they import from multiple suppliers and want a single point of regulatory contact. Whichever arrangement is used, agree it in writing before the first shipment and confirm the identification requirements that apply to the route you are using.
Technical Documentation Requirements
The technical file for the UKCA route closely mirrors the EU technical file. Key differences:
- The DoP references UK designated standards and UK legislation rather than EU harmonised standards and EU legislation (the standard may be cited with an EN or BS EN designation — what matters is that it is the applicable designated standard)
- UK authorities require technical documentation in English
- For the UKCA route, third-party conformity assessment (where required) is carried out by a UK Approved Body rather than an EU Notified Body
Otherwise, the content of the technical file — product description, design drawings, risk assessment, test reports, user manual, FPC documentation, traceability procedures — is the same as for CE marking.
10. Common UKCA Mistakes to Avoid
1. Assuming UKCA Replaced CE Overnight
Many suppliers believed that CE marking was no longer valid in the UK after Brexit. This was never the case — the UK government repeatedly extended the transition period and, in September 2024, confirmed indefinite CE recognition for construction products. Do not rush to re-certify products with UKCA if existing CE documentation is valid and accepted on the GB market.
2. Citing a Superseded or Wrong Standard Version
Standard versions change. The 2007+A1:2011 edition of EN 15102 has been superseded, and the 2019 edition narrowed its scope to roll-form wallcoverings. A DoP or certificate citing an outdated version — or the wrong standard entirely for the product form — is a red flag for professional buyers. Always check the current designated version on the UK government’s designated standards list, and confirm that the cited standard actually covers your product type, form, and intended use.
3. Confusing Northern Ireland with Great Britain
Northern Ireland follows EU rules; Great Britain follows UK rules. Applying UKCA marking to products destined only for Northern Ireland is a compliance error. Applying CE + UKNI to products for Great Britain when the assessment was by a UK Approved Body may also cause confusion. Always confirm the destination market before selecting the marking.
4. Leaving the Responsible Economic Operator Unclear
For non-UK manufacturers, the UK-based importer or authorised representative must be identified and aware of their role. Products arriving in the UK with no designated economic operator responsible for compliance documentation can be detained by market surveillance authorities.
5. Using an EU Notified Body for UKCA Marking
The UKCA route requires a UK Approved Body — an EU Notified Body cannot issue UKCA certification. If your EU Notified Body has no UK Approved Body counterpart, you will need to engage a separate UK Approved Body for the UKCA conformity assessment.
6. Not Maintaining FPC After Certification
Factory Production Control is an ongoing requirement under GB-CPR, just as under EU-CPR. Changes to formulation, raw materials, thickness, or production process may require re-testing and DoP updates. Suppliers who obtain certification but then change their product without updating documentation are non-compliant.
11. How to Verify a Supplier’s UKCA or CE Documentation
Whether your supplier presents UKCA marking or CE marking, the verification process is similar. Here is a practical checklist for UK buyers and distributors:
- Declaration of Performance (DoP). Request the DoP. It must reference the applicable designated standard for the product type and intended use, list essential characteristics, declare performance values, and include the AVCP system and the Approved Body/Notified Body reference where the system requires one.
- Test reports. Request the full test reports — not just a certificate cover page. For decorative wall coverings, reports typically cover reaction to fire (EN 13501-1 classification supported by EN 13823 / EN ISO 11925-2 testing), and chemical release testing under EN 12149 (heavy metals migration, VCM, formaldehyde), plus indoor air emissions where declared (e.g., EN 16516). Verify that the test methods match those referenced by the applicable standard version, and that the product description, thickness, and formulation match what you are buying.
- Approved Body / Notified Body verification. For UKCA: verify the body is listed on the UKMCAB database. For CE: verify the body is listed in the EU NANDO database. Check that their scope covers the designated/harmonised standard for your product.
- Standard version check. Confirm the DoP and test reports reference the current designated version of the applicable standard — not a superseded edition or the wrong standard for the product form.
- Product description match. The report must describe the exact panel — brand, model, formulation, thickness — that you are purchasing. A report for a different product line does not cover your product.
- Mark on product or packaging. Verify the UKCA or CE mark is affixed to the product, packaging, or accompanying documents as required by the applicable construction products requirements.
- Responsible economic operator. Confirm who the UK-based importer or authorised representative is, and that the identification required by the applicable route is provided.
- Report currency. Confirm the report reflects the product as currently manufactured. Formulation changes invalidate previous results.
- Technical file retention. Confirm that the technical documentation is retained and available for the period required by the applicable legislation — 10 years is the common retention period under the retained construction products framework.
- A supplier who claims “UKCA certified” but cannot provide the DoP or UK Approved Body assessment records
- A DoP or certificate citing a superseded standard version, or a standard that does not match the product form
- A DoP referencing legislation that does not apply to the claimed market route
- A CE report relabelled or paraphrased as UKCA documentation
- A report for a different thickness, formulation, or product family than the one quoted
- No UK-based importer or authorised representative identified
- UKCA marking applied to products destined for Northern Ireland (where CE is required)
Sourcing PVC Wall Panels for a UK Project?
Contact Homax Decor to confirm the compliance documentation available for your product and project market. Tell us your project location (Great Britain or Northern Ireland), the required marking (UKCA or CE), and your panel specification, and we can help identify the relevant documentation.
12. Frequently Asked Questions
Can CE-marked PVC wall panels be sold in Great Britain?
Yes. The UK government confirmed in September 2024 that CE marking for construction products continues to be recognised in Great Britain, with no end date. The Construction Products (Amendment) Regulations 2025, which came into force on 8 January 2026, extended this recognition to products compliant with the reformed EU-CPR 2024. CE-marked PVC wall panels can therefore be placed on the GB market, provided the applicable designated standard requirements are met and the necessary documentation, such as the Declaration of Performance, is in place.
Is UKCA marking mandatory for PVC wall panels in Great Britain?
No. Construction products covered by a UK designated standard can be placed on the GB market with either the UKCA mark or the CE mark. UKCA marking becomes mandatory only if the UK government withdraws its recognition of CE marking in the future, which would be subject to a minimum two-year transitional period. Some UK distributors and specifiers nevertheless request UKCA marking commercially.
What is the difference between UKCA marking and CE marking?
CE marking demonstrates conformity with EU harmonised standards under the EU Construction Products Regulation. UKCA marking demonstrates conformity with UK designated standards under the GB construction products regime. The technical requirements are currently nearly identical because UK designated standards mirror the EU harmonised standards. Where third-party conformity assessment is required, the UKCA route uses a UK Approved Body while the CE route uses an EU Notified Body, and the supporting documentation references UK legislation rather than EU legislation.
What is a UK Approved Body?
A UK Approved Body is a conformity assessment body designated under the GB construction products regime and listed on the UK Market Conformity Assessment Bodies (UKMCAB) database to perform conformity assessment activities, such as initial type testing and certification, for products covered by UK designated standards. UKAS (United Kingdom Accreditation Service) is the UK’s national accreditation body for the construction products framework. You can search for UK Approved Bodies on the UK government’s Find a Conformity Assessment Body service.
What marking is required for PVC wall panels in Northern Ireland?
Northern Ireland follows EU rules under the Windsor Framework, not GB rules. Products placed on the Northern Ireland market must bear the CE mark. If the conformity assessment was carried out by a UK Approved Body (rather than an EU Notified Body), the CE mark must be accompanied by the UKNI mark. UKCA marking alone is not accepted in Northern Ireland. Products placed on the Northern Ireland market that are assessed by an EU-based Notified Body require only the CE mark.
What is a UK Declaration of Performance?
For construction products, the UK Declaration of Performance (DoP) is prepared under the GB construction products regime. It declares the product’s essential characteristics and performance levels, references the applicable UK designated standard (e.g., EN 15102 / BS EN 15102 for decorative wall coverings), and includes the AVCP system used. The manufacturer issues the DoP and affixes the UKCA or CE mark on its basis. The DoP must be available to market surveillance authorities on request.
Do I need a UK Responsible Person to supply PVC wall panels to Great Britain?
Non-UK manufacturers should identify which economic operator is responsible for the product under the applicable GB requirements. Depending on the supply route, this is typically the UK-based importer or an authorised representative appointed by the manufacturer. That operator must ensure the conformity assessment has been carried out, the correct marking is affixed, and documentation is available to UK market surveillance authorities. The identification requirements that apply depend on the applicable legislation and route to market, so they should be confirmed for each product and supply arrangement.
What is the designated standard for PVC wall panels in the UK?
For decorative wall coverings in roll and panel form, the relevant standard is EN 15102 (also published as BS EN 15102). Note that EN 15102:2019 replaced the 2007+A1:2011 edition and narrowed its scope to roll-form wallcoverings, so the applicable standard and version depend on the product form and fixing method. Rigid PVC-U profiles used as interior wall finishes may instead fall under EN 13245-2. Because designated standards and their versions change, manufacturers should always verify the current designated version on the UK government’s designated standards list before preparing compliance documentation.
About Homax Decor: CENCHER INDUSTRY SHANGHAI CO., LTD. (brand: Homax Decor) is a manufacturer of PVC marble wall panels, WPC wall panels, and SPC flooring. Homax Decor products are tested according to relevant international standards applicable to their target markets. Contact us to confirm which compliance documentation applies to your project location, product specification, and the marking you require (CE, UKCA, or both).
Disclaimer: This article is for informational purposes only and does not constitute legal, engineering, or regulatory advice. UK construction product regulations, designated standards, and marking requirements are subject to change. Regulatory sources reviewed: UK government guidance and designated standards information available as of August 2026. Always consult the current guidance on gov.uk, your UK Approved Body, and your legal or compliance advisor for project-specific requirements.
